Effect of material composition and thickness of orthodontic aligners on the transmission and distribution of forces: an in vitro study.

OBJECTIVES: To investigate the effects of material type and thickness on force generation and distribution by aligners. MATERIALS AND METHODS: Sixty aligners were divided into six groups (n = 10): one group with a thickness of 0.89 mm using Zendura Viva (Multi-layer), four groups with a thickness of 0.75 mm using Zendura FLX (Multi-layer), CA Pro (Multi-layer), Zendura (Single-layer), and Duran (Single-layer) sheets, and one group with a thickness of 0.50 mm using Duran sheets. Force measurements were conducted using Fuji® pressure-sensitive films. RESULTS: The lowest force values, both active and passive, were recorded for the multi-layered sheets: CA Pro (83.1 N, 50.5 N), Zendura FLX (88.9 N, 60.7 N), and Zendura Viva (92.5 N, 68.5 N). Conversely, the highest values were recorded for the single-layered sheets: Duran (131.9 N, 71.8 N) and Zendura (149.7 N, 89.8 N). The highest force was recorded at the middle third of the aligner, followed by the incisal third, and then the cervical third. The net force between the incisal and cervical thirds (FI-FC) showed insignificant difference across different materials. However, when comparing the incisal and middle thirds, the net force (FI-FM) was higher with single-layered materials. Both overall force and net force (FI-FM) were significantly higher with 0.75 mm compared to those with a thickness of 0.50 mm. CONCLUSIONS: Multi-layered aligner materials exert lower forces compared to their single-layered counterparts. Additionally, increased thickness in aligners results in enhanced retention and greater force generation. For effective bodily tooth movement, thicker and single-layered rigid materials are preferred. CLINICAL RELEVANCE: This research provides valuable insights into the biomechanics of orthodontic aligners, which could have significant clinical implications for orthodontists. Orthodontists might use this information to more effectively tailor aligner treatments, considering the specific tooth movement required for each individual patient. In light of these findings, an exchangeable protocol for aligner treatment is suggested, which however needs to be proven clinically. This protocol proposes alternating between multi-layered and single-layered materials within the same treatment phase. This strategy is suggested to optimize treatment outcomes, particularly when planning for a bodily tooth movement.

Orthodontics and Endodontics Clinical Practice Correlation: A Narrative Review.

Research on the connection between endodontic therapy and orthodontics is lacking. This overview of the literature synthesizes the findings from the fields of orthodontics and endodontics and explains how they are related. Beginning with the diagnosis, treating the patient at the appropriate time, moving endodontically treated teeth and traumatized teeth, resorbing roots by orthodontic mechanics, and managing traumatized teeth with orthodontic therapy. Multiple electronic databases were utilized including (PubMed, Scopus, Science Direct, and Web of Science) to perform manual literature searches. A total of 31 articles were reviewed and summarized in this paper in keywords like "Endodontically Treated Teeth and Orthodontic Treatment," "Endodontically Treated Tooth and Orthodontic Movement," "Orthodontic Treatment in RCT Teeth," "Root Canal Treatment with Orthodontic Movement," "Trauma with Orthodontic Movement," "Orthodontic and Endodontic." Orthodontic treatment of endodontically treated and traumatized teeth is a subject of controversy. The lack of research on the topic makes it a hard decision to make when to treat these teeth. Especially given that both orthodontic and endodontic treatments have multiple consequences on each other's outcomes. Thus, it is crucial for clinicians to understand how they integrate and have a guideline to refer to during decision-making. Successful orthodontic tooth movement could be carried out immediately after endodontic treatment. However, traumatized teeth need a follow-up period before initiating orthodontic movement, which ranges from three months to 12 months depending on the type of trauma and severity. Careful radiographic and clinical follow-up should be done during the healing period. Collaborative teamwork is important between orthodontists and endodontists for the success of treatment, and to achieve satisfactory outcomes.

Effect of Lithium on Orthodontic Tooth Movement: a Systematic Review of Animal Studies.

Objective: This study aimed to systematically review the effect of lithium on orthodontic tooth movement (OTM). Methods: The focus question was "does lithium have an effect on OTM?" A systematic search was conducted using indexed databases and the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines were followed. The quality assessment of the selected studies was performed according to the systematic review center for laboratory animal experimentation. Results: Five of the initially identified 656 articles fulfilled the eligibility criteria and were selected for this review. The studies reported that lithium administration lowered the rate of OTM by inducing a reduction in the number of osteoclasts and possibly inhibiting osteoclastogenesis. These studies further showed an increase in bone density and bone volume by promoting the Wnt/ß-catenin signaling pathway and osteoblastogenesis. It was also noted that lithium reduced orthodontically induced root resorption during experimental OTM. Further, standardized studies are warranted to understand the impact of lithium in OTM. Overall, the risk of bias for 3 studies was very high, high in 1 study, and moderate in 1 study. Conclusion: On an experimental level in animals, lithium decreased the rate of OTM during the active treatment phase by increasing bone density and bone volume and reducing root resorption. In addition, lithium may enhance alveolar bone formation during orthodontic retention. Clinically, this may impact the orthodontic treatment duration in patients receiving lithium, and further studies are needed to understand the true impact of lithium on OTM.

Systematic review on effects of experimental orthodontic tooth displacement on brain activation assessed by fMRI.

BACKGROUND: Orthodontic treatment is often accompanied by discomfort and pain in patients, which are believed to be a result of orthodontic tooth displacement caused by the mechanical forces exerted by the orthodontic appliances on the periodontal tissues. These lead to change blood oxygen level dependent response in related brain regions. OBJECTIVE: This systematic review aims to assess the impact of experimental orthodontic tooth displacement on alterations in central nervous system activation assessed by tasked based and resting state fMRI. MATERIALS AND METHODS: A literature search was conducted using online databases, following PRISMA guidelines and the PICO framework. Selected studies utilized magnetic resonance imaging to examine the brain activity changes in healthy participants after the insertion of orthodontic appliances. RESULTS: The initial database screening resulted in 791 studies. Of these, 234 were duplicates and 547 were deemed irrelevant considering the inclusion and exclusion criteria. Of the ten remaining potential relevant studies, two were excluded during full-text screening. Eight prospective articles were eligible for further analysis. The included studies provided evidence of the intricate interplay between orthodontic treatment, pain perception, and brain function. All of the participants in the included studies employed orthodontic separators in short-term experiments to induce tooth displacement during the early stage of orthodontic treatment. Alterations in brain activation were observed in brain regions, functional connectivity and brain networks, predominantly affecting regions implicated in nociception (thalamus, insula), emotion (insula, frontal areas), and cognition (frontal areas, cerebellum, default mode network). CONCLUSIONS: The results suggest that orthodontic treatment influences beyond the pain matrix and affects other brain regions including the limbic system. Furthermore, understanding the orthodontically induced brain activation can aid in development of targeted pain management strategies that do not adversely affect orthodontic tooth movement. Due to the moderate to serious risk of bias and the heterogeneity among the included studies, further clinical trials on this subject are recommended.

Low-intensity pulsed ultrasound reduces alveolar bone resorption during orthodontic treatment via Lamin A/C-Yes-associated protein axis in stem cells.

BACKGROUND: The bone remodeling during orthodontic treatment for malocclusion often requires a long duration of around two to three years, which also may lead to some complications such as alveolar bone resorption or tooth root resorption. Low-intensity pulsed ultrasound (LIPUS), a noninvasive physical therapy, has been shown to promote bone fracture healing. It is also reported that LIPUS could reduce the duration of orthodontic treatment; however, how LIPUS regulates the bone metabolism during the orthodontic treatment process is still unclear. AIM: To investigate the effects of LIPUS on bone remodeling in an orthodontic tooth movement (OTM) model and explore the underlying mechanisms. METHODS: A rat model of OTM was established, and alveolar bone remodeling and tooth movement rate were evaluated via micro-computed tomography and staining of tissue sections. In vitro, human bone marrow mesenchymal stem cells (hBMSCs) were isolated to detect their osteogenic differentiation potential under compression and LIPUS stimulation by quantitative reverse transcription-polymerase chain reaction, Western blot, alkaline phosphatase (ALP) staining, and Alizarin red staining. The expression of Yes-associated protein (YAP1), the actin cytoskeleton, and the Lamin A/C nucleoskeleton were detected with or without YAP1 small interfering RNA (siRNA) application via immunofluorescence. RESULTS: The force treatment inhibited the osteogenic differentiation potential of hBMSCs; moreover, the expression of osteogenesis markers, such as type 1 collagen (COL1), runt-related transcription factor 2, ALP, and osteocalcin (OCN), decreased. LIPUS could rescue the osteogenic differentiation of hBMSCs with increased expression of osteogenic marker inhibited by force. Mechanically, the expression of LaminA/C, F-actin, and YAP1 was downregulated after force treatment, which could be rescued by LIPUS. Moreover, the osteogenic differentiation of hBMSCs increased by LIPUS could be attenuated by YAP siRNA treatment. Consistently, LIPUS increased alveolar bone density and decreased vertical bone absorption in vivo. The decreased expression of COL1, OCN, and YAP1 on the compression side of the alveolar bone was partially rescued by LIPUS. CONCLUSION: LIPUS can accelerate tooth movement and reduce alveolar bone resorption by modulating the cytoskeleton-Lamin A/C-YAP axis, which may be a promising strategy to reduce the orthodontic treatment process.

Effectiveness of low frequency vibration on the rate of canine retraction: a randomized controlled clinical trial.

To investigate the effectiveness of AcceleDent Aura vibrating device on the rate of canine retraction. Thirty-two patients requiring extraction of upper first premolars and canine retraction were randomly allocated with a 1:1 ratio into either no-appliance group or the AcceleDent Aura appliance group. Canine retraction was done applying 150gm of retraction force using NiTi coil springs on 16 × 22 stainless steel archwires. The duration of the study was 4 months. Models were collected and digitized directly after extraction of upper first premolars and at monthly intervals during canine retraction for recording the monthly as well as the total distance moved by the canine. Digitized models were superimposed on the initial model and data were statistically analyzed. Anchorage loss, rotation, tipping, torque and root condition were evaluated using cone beam computed tomography imaging. Pain was evaluated by visual analog scale. No patients were dropped-out during this study. There was no statistically significant difference between both groups regarding the total distance travelled by the canine (P = 0.436), as well as the rate of canine retraction per month (P = 0.17). Root condition was the same for the two groups. Regarding the pain level, there was no statistically significant difference between the two groups at day 0 (P = 0.721), after 24 h (P = 0.882), after 72 h (P = 0.378) and after 7 days (P = 0.964). AcceleDent Aura was not able to accelerate orthodontic tooth movement. Pain level couldn't be reduced by vibrational force with an AcceleDent device during orthodontic treatment. Root condition was not affected by the vibrational forces.

Effect of thermomechanical aging on force system of orthodontic aligners made of different thermoformed materials : An in vitro study.

PURPOSE: The aim was to investigate the effect of aging by thermocycling and mechanical loading on forces and moments generated by orthodontic clear aligners made from different thermoplastic materials. METHODS: A total of 25 thermoformed aligners made from 5 different materials, i.e., Essix ACE® and Essix® PLUS™ (Dentsply Sirona, Bensheim, Germany), Invisalign® (Align Technology, San Jose, CA, USA), Duran®+ (Iserlohn, Germany), Zendura™ (Fremont, CA, USA), underwent a 14-day aging protocol involving mechanical loading (a 0.2 mm vestibular malalignment of the upper left second premolar [tooth 25]) and thermocycling in deionized water (temperature range 5-55 °C). The 3D forces/moments exerted on tooth 25 of a resin model were measured at three time points: before aging (day 0), after 2 days and after 14 days of aging. RESULTS: Before aging, extrusion-intrusion forces were 0.6-3.0 N, orovestibular forces were 1.7-2.3 N, and moments as mesiodistal rotation were 0.3-42.1 Nmm. In all directions, multilayer Invisalign® exhibited the lowest force/moment magnitudes. After aging, all materials showed a significant force/moment decay within the first 2 days, except Invisalign® for orovestibular and vertical translation. However, following thermomechanical aging, Duran®+ and Zendura™ aligners had equivalent or even higher vestibular forces (direction of mechanical load). CONCLUSION: Thermomechanical aging significantly reduced forces and moments during the first 48 h. Multilayer aligner materials exhibit lower initial forces and moments than single-layer ones, and were less influenced by aging. Material hardening was observed after subjecting some of the aligner materials to mechanical loading. Thus, orthodontists should be aware of possible deterioration of orthodontic aligners over time. This work also sheds light on how material selection impacts the mechanical behavior of aligners and may provide valuable guidance regarding optimal timing for the aligner changing protocol.

Effect of orthodontic space closure on dental pulp sensitivity. Prospective clinical trial.

BACKGROUND: Orthodontic tooth movement (OTM) is a biological process that can influence the function of the pulp, including its innervation. The excitability of the nerve fibres of the pulp may be altered by forces exerted on the nerve fibres or by reduced blood flow to the pulp. The aim of this clinical study was to evaluate the sensitivity of the dental pulp during levelling and during the phase of space closure, to assess the role of certain controlled risk factors. METHODS: Twenty-two adolescent participants requiring orthodontic space closure in transcanine sector were enrolled in a prospective clinical study. Patients were observed before OTM, after levelling and 1 month during active space closure. The sensitivity threshold of the pulp was measured using the electric pulp test (EPT). Dental models were obtained using an intraoral scanner, allowing measurement of interdental distances and calculation of OTM speed. The teeth were categorized according to position and tooth type. RESULTS: The EPT values increased significantly during orthodontic treatment (one-way RM-ANOVA, P = .014). There was a significant difference in EPT values between the tooth categories. Teeth with a single root adjacent to the residual space had the highest EPT thresholds (two-way RM-ANOVA, P < .001; Holm-Sidak, P < .05). CONCLUSIONS: OTM reduced pulpal sensitivity. Pulpal sensitivity during active space closure was similar to sensitivity during the levelling phase. The pulpal sensitivity of molars was less affected by OTM than that of single-rooted teeth, while teeth closer to the gap had a significantly higher pulpal sensitivity threshold during active OTM.

Dopamine promotes osteogenic differentiation of PDLSCs by activating DRD1 and DRD2 during orthodontic tooth movement via ERK1/2 signaling pathway.

Introduction: Orthodontic tooth movement (OTM) involves complex interactions between mechanical forces and periodontal tissue adaptation, mainly mediated by periodontal ligament cells, including periodontal ligament stem cells (PDLSCs), osteoblasts, and osteoclasts. Dopamine (DA), a neurotransmitter known for its critical role in bone metabolism, is investigated in this study for its potential to enhance osteogenic differentiation in PDLSCs, which are pivotal in OTM. This study examined the potential of DA to facilitate OTM by binding to DA receptors (D1R and D2R) and activating the ERK1/2 signaling pathway. We propose that DA's interaction with these receptors on PDLSCs could enhance osteogenic differentiation, thereby accelerating bone remodeling and reducing the duration of orthodontic treatments, which offering a novel approach to improve clinical outcomes in orthodontic care. Methods: This study utilized a rat OTM model, micro-CT, histological analyses, and in vitro assays to investigate dopamine's effect on osteogenesis. PDLSCs were cultured and treated with DA, and cytotoxicity, osteogenic differentiation, gene and protein expression assessed. Results: Dopamine administration significantly increased trabecular bone density and osteogenic marker expression in an OTM rat model. In vitro, DA at 10 nM optimally promoted human PDLSCs osteogenesis without affecting proliferation. Blocking DA receptors or inhibiting the ERK1/2 pathway attenuated these effects, underscoring the importance of dopaminergic signaling in tension-induced osteogenesis during OTM. Conclusion: Taken together, our study reveals that local dopamine administration at a concentration of 10 nM not only enhances tension-induced osteogenesis in vivo but also significantly promotes osteogenic differentiation of PDLSCs in vitro through D1 and D2 receptor-mediated ERK1/2 signaling pathway activation.

Effect of age on orthodontic tooth movement in mice.

Background/purpose: The number of middle-aged and elderly orthodontic patients is increasing due to changes in age composition. It is important to investigate the detailed mechanisms of bone remodeling in orthodontic tooth movement (OTM) in the elderly. However, there are few reports on the mechanism of tooth movement in the elderly. The purpose of the present study was to analyze OTM and osteoclastogenesis in aged mice and to elucidate the mechanism. Materials and methods: It has been reported that tumor necrosis factor (TNF)-α plays an important role in osteoclast formation and OTM. First, 8-week-old and 78-week-old male C57BL/6J mice were subcutaneously injected with TNF-α into the calvaiae, and micro-CT, tartrate-resistant acid phosphatase (TRAP) staining, and real-time PCR were performed to evaluate osteoclast formation and bone resorption. Furthermore, osteoclastogenesis by TNF-α and receptor activator of nuclear factor-kappa B ligand (RANKL) using bone marrow cells was evaluated in vitro. Finally, a nickel-titanium closed-coil spring was attached, mesial movement of the maxillary left first molar was performed, and tooth movement distance and osteoclast formation were evaluated. Results: Compared to 8-week-old mice, 78-week-old mice had decreased TNF-α-induced bone resorption, osteoclastogenesis, and TRAP and cathepsin K expression in the calvariae. In vitro osteoclast formation also decreased in 78-week-old mice. Furthermore, tooth movement distance and osteoclastogenesis were reduced. Conclusion: OTM decreased in aged mice, which was shown to be caused by a decrease in osteoclastogenesis. Therefore, it was suggested that it is necessary to keep in mind that tooth movement may be suppressed when treating elderly patients.

Effect of laser corticotomy on canine retraction rate: a split-mouth randomized clinical trial.

BACKGROUND: This study assessed the effect of corticotomy with Er: YAG (erbium-doped yttrium aluminium garnet) laser on the rate of canine retraction. METHODS: This randomized split-mouth controlled clinical trial was conducted on 12 patients undergoing orthodontic treatment with extraction of maxillary first premolars. Following initial leveling and alignment, an alginate impression was made from the maxillary arch, and Er: YAG laser corticotomy was performed in one of the maxillary quadrants of each patient. Canine retraction was started immediately after corticotomy by placement of nickel-titanium (NiTi) closed coil springs at both sides. At the end of each month, alginate records were repeated for 4 months. Study models were scanned, and the anteroposterior movement of canine was quantified bilaterally. Pain was also measured by a visual analog scale (VAS). Probing depth (PPD) of canines and two adjacent teeth was also evaluated and pulp vitality was assessed by performing the cold test. Data were analyzed by paired and independent t-test and one-way ANOVA (alpha = 0.05). RESULTS: The rate of canine retraction was significantly greater in the laser-assisted corticotomy quadrant than the control (P < 0.05). No significant difference existed in posterior anchorage loss, canine rotation angle, PPD, pulp vitality, or pain score between two groups (P > 0.05). CONCLUSIONS: Flapless Er: YAG laser corticotomy significantly enhanced canine retraction rate with no adverse effect on other parameters.

Comparing the Efficacy of Different Archwire Materials in Accelerating Orthodontic Tooth Movement.

Background: Orthodontic treatment is commonly used to correct misaligned teeth and improve dental aesthetics and function. Archwires play a crucial role in this treatment by exerting forces on teeth, prompting them to shift into desired positions. Materials and Methods: For this experimental study, 60 participants requiring orthodontic treatment were selected and divided into three groups: Group A, treated with stainless steel archwires; Group B, treated with nickel-titanium archwires; and Group C, treated with beta-titanium archwires. Standardized orthodontic procedures were followed for all participants. The rate of tooth movement was measured over a period of 6 months using digital models and a calibrated measurement technique. Results: The study revealed notable differences in the rate of orthodontic tooth movement among the three groups. Group B (nickel-titanium archwires) demonstrated the highest mean rate of tooth movement, with an average of 1.5 mm per month. Group A (stainless steel archwires) exhibited a mean rate of 1.2 mm per month, while Group C (beta-titanium archwires) showed the lowest mean rate at 0.9 mm per month. Conclusion: In conclusion, this study highlights the varying efficacy of different archwire materials in accelerating orthodontic tooth movement. Nickel-titanium archwires exhibited the highest rate of tooth movement compared to stainless steel and beta-titanium archwires.

Evaluation of Micro-Osteoperforations in Expediting Orthodontic Tooth Movement in Adult Patients.

Background: Orthodontic tooth movement, the process of aligning teeth, can often be time-consuming, particularly in adult patients. Micro-osteoperforations (MOPs) have emerged as a potential technique to accelerate this process. Materials and Methods: A sample of 30 adult patients undergoing orthodontic treatment was selected. The patients were divided into two groups: an experimental group (EG) receiving MOPs and a control group (CG) without MOPs. Standard orthodontic treatment was administered to both groups. The rate of tooth movement was measured using digital models and recorded in millimeters per month. Pain levels reported by patients were also noted. The data were analyzed using basic statistical methods. Results: The EG demonstrated a significantly higher rate of orthodontic tooth movement compared to the CG. The average rate of tooth movement in the EG was 1.5 millimeters per month, while the CG exhibited an average rate of 0.8 millimeters per month. Additionally, pain levels reported by patients in the EG were slightly elevated immediately after MOPs but subsided within a few days. Conclusion: The findings of this study suggest that MOPs can effectively expedite orthodontic tooth movement in adult patients.

Accelerated Orthodontic Treatment Using Photobiomodulation: A Randomized Clinical Trial.

Background: Orthodontic treatment (OT) aims to align and correct teeth positions. However, conventional treatment methods often require a considerable amount of time. Photobiomodulation (PBM) has emerged as a potential solution to OT. Materials and Methods: The study included 60 patients, divided equally into two groups: the PBM group and the control group. Patients in the PBM group received light therapy sessions applied directly to the OT area during each visit. Both groups underwent regular orthodontic adjustments. Treatment duration, changes in tooth alignment, and patient discomfort were evaluated. Statistical analysis was performed to compare the outcomes between the groups. Results: The results of the study indicated that the PBM group experienced a statistically significant reduction in treatment duration compared to the control group. Moreover, there were noticeable improvements in tooth alignment in both groups. Patients in the PBM group reported minimal discomfort during the treatment process. These findings suggest that PBM has the potential to expedite OT without compromising its effectiveness. Conclusion: In conclusion, this randomized clinical trial demonstrates that PBM can be an effective approach to accelerate OT. The technique led to a significant reduction in treatment duration and was well-tolerated by patients.

Clinical effectiveness of regenerative periodontal surgery and orthodontic tooth movement with clear aligners in stage IV periodontitis: a case series.

OBJECTIVES: To evaluate the clinical effectiveness of regenerative treatment of intra-bony defects in combination with consecutive orthodontic therapy (OT) with clear aligners in stage IV (type 2) periodontitis. METHOD AND MATERIALS: Ten patients with a total of 103 intra-bony defects were analyzed after regenerative surgery using collagen-deproteinized bovine bone mineral with or without collagen membrane or enamel matrix derivative followed by OT with clear aligners. Changes in radiographic bone level (rBL) and probing pocket depths (PPD) were evaluated after 1 year (T1) and at final splinting (T2) after orthodontic tooth movement. RESULTS: Mean rBL gain was significant with 2.13 mm (±1.64 mm) after 1 year (T1) and 3.02 mm (±2.00mm) at final splinting (T2). Mean PPD was significantly reduced from 5.40 mm (±1.80 mm)at baseline to 3.78 mm (±1.73 mm) at T1 and remained stable with 3.73 mm (±1.70 mm)at T2. Pocket closure (PPD< 4mm) was accomplished in 76% of all defects. Tooth loss amounted to 2.9%. CONCLUSION: Within the limitations of the retrospective study design, the findings suggest that the interdisciplinary treatment of periodontitis stage IV by regenerative periodontal surgery and consecutive OT with clear aligners can lead to favorable results.

Treatment Efficiency of Maxillary and Mandibular Orovestibular Tooth Expansion and Compression Movements with the Invisalign® System in Adolescents and Adults.

OBJECTIVES: Aligners are an effective and esthetic orthodontic treatment option for permanent and mixed dentition. There are only a few studies dealing with the effectiveness of orovestibular tooth movement using aligners and applying adequate examination methods. In the present retrospective study, the aligner efficiency of orovestibular movements for the entire dentition was systematically evaluated using 3D superimposition, taking into account the influence of jaw, tooth type and Invisalign® system. METHODS: Group 1 (n = 18 adults, Invisalign®) and Group 2 (n = 17 adolescents, Invisalign® Teen) were treated with Invisalign® Ex30 aligner material and Invisalign® specific auxiliary means. In this non-interventional retrospective study, pre- and post-treatment maxillary and mandibular plaster cast models were scanned and superimposed with ClinChecks® via Surface-Surface Matching Algorithm on unmoved teeth providing stable references. Effectivity of planned versus clinically realized movements was evaluated for each tooth. Statistics were performed with a t-test and Bonferroni-Holm correction (α = 0.05). RESULTS: Orovestibular movement efficiency was excellent without statistical significance regarding jaw, tooth type or Invisalign® system. Mandibular translational tooth movements were highly effective, and outstanding for premolars (91-98%). Maxillary translational tooth movements were successful for incisors and premolars, but less effective for canines and molars. Almost all teeth were moderately or very effectively corrected by crown tipping, performing better for mandibular (70-92%) than maxillary (22-31%) canines as much as for adolescent upper front teeth (81-85%) and lower canines (92%). CONCLUSIONS: Aligners are able to effectively implement translational orovestibular movements, supported by tilting the crowns for even more efficient implementation of the movements. This phenomenon was observed in our studies for all teeth in both jaws, regardless of the Invisalign® system used. Treatment planning should nevertheless take into account the individual patient parameters with regard to the movements to be performed in order to make the aligner therapy as successful as possible in terms of realizing the desired therapeutic goal.

Digital setup accuracy for moderate crowding correction with fixed orthodontic appliances: a prospective study.

OBJECTIVES: To evaluate the accuracy of a semi-automatic 3D digital setup process in predicting the orthodontic treatment outcome achieved by labial fixed appliances. SUBJECTS AND METHODS: Twenty-five adult patients (18 to 24 years old) with class I malocclusion and moderate crowding were prospectively enrolled and received treatment on both jaws through the straight-wire technique. Prior to treatment commencement, a semi-automatic digital setup simulating the predicted treatment outcome was performed for each patient through Orthoanalyzer software (3Shape®, Copenhagen, Denmark) to obtain the prediction model. This was compared to the final outcome model through 3D superimposition methods. Metric variables and inspection of color-coded distance maps were used to detect how accurately the digital setup predicts the actual treatment outcome. RESULTS: The mean absolute distances (MAD) between the superimposed dental arches of the predicted and the final models were: 0.77 ± 0.13 mm following superimposition on the palate, 0.52 ± 0.06 mm following superimposition on the maxillary dental arch, and 0.55 ± 0.15 mm following superimposition on the mandibular dental arch. The MAD at the palatal reference area was 0.09 ± 0.04 mm. Visualization of color-coded distance maps indicated that the digital setup accurately predicted the final teeth position in a few cases. Almost half of the cases had posteriorly wider upper and lower dental arches and palatally/lingually positioned or inclined anterior teeth, whereas the rest still showed errors within 2-3 mm, distributed over the entire dental arches with no distinct pattern. CONCLUSIONS: The accuracy of semi-automatic prediction of the labial fixed appliance treatment outcome in Class I cases with moderate crowding is not yet sufficient. While average measures showed deviations less than 1 mm, examination of individual color-coded distance maps revealed significant disparities between the simulated and the actual results.

Aucubin produces anti-osteoporotic effects under mechanical stretch stress and orthodontic tooth movement.

Aucubin (AU), an iridoid glycoside extracted from Eucommia ulmoides, exerts anti-osteoporotic effects by promoting osteogenesis, as reported in previous studies. Here, we investigated the effects of AU under mechanical stretch stress. MC3T3-E1 cells were treated with dexamethasone (DEX) in vitro and subjected to mechanical stretch stress to establish an osteoporotic orthodontic force cell model. AU treatment increased the mRNA and protein expressions of BMP2, OPN, RUNX2, COL-1 and other osteogenic differentiation factors in MC3T3-E1 cells. Furthermore, we established an in vivo orthodontic tooth movement (OTM) model of osteoporosis. Serum parameter detection of ALP concentration, radiography of the femur, hematoxylin-eosin (HE) staining, and micro-CT of the maxilla confirmed that AU could partially reverse the damage induced by DEX. Immunohistochemical (IHC) analysis showed that AU increased the expression of COL-1, OCN, and OPN on the tension side of the periodontium. In conclusion, AU treatment promotes osteogenic differentiation under mechanical stretch stress and positively affects bone remodeling during OTM in DEX-induced osteoporosis.

Micro-Osteoperforations Accelerate Tooth Movement without Exacerbating the Progression of Root Resorption in Rats.

A recent study reported that micro-osteoperforations (MOPs) accelerated tooth movement by activating alveolar bone remodeling. However, very little is known about the relationship between MOPs and external apical root resorption during orthodontic treatment. In this study, in order to investigate the mechanism through which MOPs accelerate tooth movement without exacerbating the progression of root resorption, we measured the volume of the resorbed root, and performed the terminal deoxynucleotidyl transferase (TdT)-mediated dUTP-biotin nick-end labeling (TUNEL) method on exposed MOPs during experimental tooth movements in rats. Male Wistar rats (11 weeks old) were divided into three groups: 10 g orthodontic force (optimal force) applied to the maxillary first molar (optimal force: OF group), 50 g orthodontic force application (heavy force: HF group), and 10 g force application plus three small perforations of the cortical plate (OF + MOPs group). On days 1, 4, 7, 10, and 14 after force application, the tooth movement and root volume were investigated by micro-computed tomography. Furthermore, the number of apoptotic cells in the pressured sides of the periodontal ligament (PDL) and surrounding hard tissues were determined by TUNEL staining. The OF + MOPs group exhibited a 1.8-fold increase in tooth movement on days 7, 10, and 14 compared with the OF group. On days 14, the HF group had a higher volume of root loss than the OF and OF + MOPs groups. On the same day, the number of TUNEL-positive cells in the HF group increased at the root (cementum) site whereas that in the OF group increased at the alveolar bone site. Furthermore, the number of TUNEL-positive cells in the OF + MOPs group increased at the alveolar bone site compared with the OF group. These results suggest that MOPs accelerate orthodontic tooth movement without exacerbating the progression of root resorption.

The biological effects of Piezocision™ on bone for accelerated tooth movement: A systematic review of animal studies.

OBJECTIVES: This systematic review aimed to assess the biological response at tissue, cellular, and molecular levels following Piezocision™ surgery, and its efficacy in accelerating orthodontic tooth movement. MATERIAL AND METHODS: A systematic review of the literature was conducted across 4 databases following the PRISMA guidelines up to May 2022. Prospective controlled animal studies involving healthy animals under active orthodontic treatment assisted by corticotomy performed with a piezotome (Piezocision™) published in the English language without time restrictions were included. The article selection, data extraction and risk of bias assessment (SYRCLE tool) were performed by two independent blinded review authors. RESULTS: Out of 738 articles screened, 10 studies were included with various level of bias. Biological responses were categorized into tissue, cellular, and molecular levels. Tissue-level changes included a global decrease in bone mineral content post-Piezocision™. At the cellular level, increased bone turnover activity was noted. Molecularly, elevated RANKL and OPG expression, along with increased TRAP+ and cytokines, were observed after Piezocision™. Studies confirmed Piezocision's efficacy, reporting 1.35 to 3.26 times faster tooth movements, peaking between the 3rd and 50th day post-surgery. Biological responses were transient, reversible, and proportional to surgical insult, with reactivation possible through a second Piezocision™. CONCLUSIONS: After Piezocision™ surgery, a transient and reversible biological response was described at the tissue, cellular and molecular levels, which induced faster orthodontic tooth movements. This biological response could be re-activated by an additional Piezocision™ and is proportional to the surgical injury. SYSTEMATIC REVIEW REGISTRATION: Prospero CRD42022303237.